home *** CD-ROM | disk | FTP | other *** search
/ Tech Arsenal 1 / Tech Arsenal (Arsenal Computer).ISO / tek-20 / gen21.zip / GEN9.DAT < prev    next >
Text File  |  1991-11-22  |  13KB  |  305 lines

  1. 256I-3.7   B 9-8   Lde = 468/Fmhz, Lde = 468/14.0|Lde = 33.4,  ie. Lde ≈ 33 feet
  2. How long is the driven element of a Yagi antenna for
  3. 14.0-MHz?
  4. A. Approximately 17 feet
  5. B. Approximately 33 feet
  6. C. Approximately 35 feet
  7. D. Approximately 66 feet
  8. *
  9. 257I-3.8   B 9-8   Lde = 468/Fmhz, Lde = 468/21.1|Lde = 22.18,     Ldr = .95*Lde|Ldr = .95*22.18,   Ldr = 21.07
  10. How long is the director element of a Yagi antenna for
  11. 21.1-MHz?
  12. A. Approximately 42 feet
  13. B. Approximately 21 feet
  14. C. Approximately 17 feet
  15. D. Approximately 10.5 feet
  16. *
  17. 258I-3.9   C 9-8   Lde = 468/Fmhz, Lde = 468/28.1|Lde = 16.65,     Lr = 1.05*Lde|Lr = 1.05*16.65,    Lr = 17.48
  18. How long is the reflector element of a Yagi antenna for
  19. 28.1-MHz?
  20. A. Approximately 8.75 feet
  21. B. Approximately 16.6 feet
  22. C. Approximately 17.5 feet
  23. D. Approximately 35 feet
  24. *
  25. 259I-5.1   D 9-3   ≈ 73 Ω real, ie. resistive
  26. What is the feed-point impedance for a half-wavelength dipole HF
  27. antenna suspended horizontally one-quarter wavelength or more
  28. above the ground?
  29. A. Approximately 50 ohms, resistive
  30. B. Approximately 73 ohms, resistive and inductive
  31. C. Approximately 50 ohms, resistive and capacitive
  32. D. Approximately 73 ohms, resistive
  33. *
  34. 260I-5.2   B 9-11  ≈ 36 Ω
  35. What is the feed-point impedance of a quarter-wavelength vertical
  36. HF antenna with a horizontal ground plane?
  37. A. Approximately 18 ohms
  38. B. Approximately 36 ohms
  39. C. Approximately 52 ohms
  40. D. Approximately 72 ohms
  41. *
  42. 261I-5.3   D 9-13  Raises feed-point impedance to ≈ 50 Ω
  43. What is an advantage of downward sloping radials on a ground-
  44. plane antenna?
  45. A. Sloping the radials downward lowers the radiation angle
  46. B. Sloping the radials downward brings the feed-point impedance
  47.    close to 300 ohms
  48. C. Sloping the radials downward allows rainwater to run off the
  49.    antenna
  50. D. Sloping the radials downward brings the feed-point impedance
  51.    closer to 50 ohms
  52. *
  53. 262I-5.4   B 9-13  Raises impedance compared|to being straight out
  54. What happens to the feed-point impedance of a ground-plane
  55. antenna when the radials slope downward from the base of the
  56. antenna?
  57. A. The feed-point impedance decreases
  58. B. The feed-point impedance increases
  59. C. The feed-point impedance stays the same
  60. D. The feed-point impedance becomes purely capacitive
  61. *
  62. 263I-6.1   C 9-11  More directivity in both the planes|The greater the directivity of the |antenna, the greater the gain      
  63. Compared to a dipole antenna, what are the directional radiation
  64. characteristics of a cubical quad HF antenna?
  65. A. The quad has more directivity in the horizontal plane but less
  66.    directivity in the vertical plane
  67. B. The quad has less directivity in the horizontal plane but more
  68.    directivity in the vertical plane
  69. C. The quad has more directivity in both horizontal and vertical
  70.    planes
  71. D. The quad has less directivity in both horizontal and vertical
  72.    planes
  73. *
  74. 264I-6.2   A 9-3   If installed parallel to the earth, |maximun radiation is at 90° to the  |antenna wire, ie. a figure-8 pattern
  75. What is the radiation pattern of an ideal half-wavelength dipole
  76. HF antenna?
  77. A. If it is installed parallel to the earth, it radiates well in
  78.    a figure-eight pattern at right angles to the antenna wire
  79. B. If it is installed parallel to the earth, it radiates well in
  80.    a figure-eight pattern off both ends of the antenna wire
  81. C. If it is installed parallel to the earth, it radiates equally
  82.    well in all directions
  83. D. If it is installed parallel to the earth, the pattern will have
  84.    two lobes on one side of the antenna wire, and one larger lobe
  85.    on the other side
  86. *
  87. 265I-6.3   B 9-3   If the antenna is too close to ground|the pattern is distorted
  88. How does proximity to the ground affect the radiation pattern
  89. of a horizontal dipole HF antenna?
  90. A. If the antenna is too far from the ground, the pattern
  91.    becomes unpredictable
  92. B. If the antenna is less than one-half wavelength from the
  93.    ground, reflected radio waves from the ground distort the
  94.    radiation pattern of the antenna
  95. C. A dipole antenna's radiation pattern is unaffected by its
  96.    distance to the ground
  97. D. If the antenna is less than one-half wavelength from the
  98.    ground, radiation off the ends of the wire is reduced
  99. *
  100. 266I-6.4   C 9-10  Power radiated forward compared to |the power radiated to the rear, ie.|in exactly the opposite direction  
  101. What does the term antenna front-to-back ratio mean?
  102. A. The number of directors versus the number of reflectors
  103. B. The relative position of the driven element with respect
  104.    to the reflectors and directors
  105. C. The power radiated in the major radiation lobe compared
  106.    to the power radiated in exactly the opposite direction
  107. D. The power radiated in the major radiation lobe compared
  108.    to the power radiated 90 degrees away from that direction
  109. *
  110. 267I-6.5   D 9-5   Radiated power will increase in the|direction of the added element and |decrease in the opposite direction 
  111. What effect upon the radiation pattern of an HF dipole antenna
  112. will a slightly smaller parasitic parallel element located a few
  113. feet away in the same horizontal plane have?
  114. A. The radiation pattern will not change appreciably
  115. B. A major lobe will develop in the horizontal plane, parallel
  116.    to the two elements
  117. C. A major lobe will develop in the vertical plane, away from
  118.    the ground
  119. D. If the spacing is greater than 0.1 wavelength, a major lobe
  120.    will develop in the horizontal plane to the side of the driven
  121.    element toward the parasitic element
  122. *
  123. 268I-6.6   C 9-5   The direction that has the greatest|amount of radiated power
  124. What is the meaning of the term main lobe as used in reference to
  125. a directional antenna?
  126. A. The direction of least radiation from an antenna
  127. B. The point of maximum current in a radiating antenna element
  128. C. The direction of maximum radiated field strength from a
  129.    radiating antenna
  130. D. The maximum voltage standing wave point on a radiating element
  131. *
  132. 269I-7.1   A 9-13  Radius of the conductors |and spacing between them 
  133. Upon what does the characteristic impedance of a parallel-conductor
  134. antenna feed line depend?
  135. A. The distance between the centers of the conductors and the
  136.    radius of the conductors
  137. B. The distance between the centers of the conductors and the
  138.    length of the line
  139. C. The radius of the conductors and the frequency of the signal
  140. D. The frequency of the signal and the length of the line
  141. *
  142. 270I-7.2   B 9-15  The two most common impedances used |for coax feedlines are 50 Ω and 75 Ω|75 Ω is also used for TV and video  
  143. What is the characteristic impedance of various coaxial cables
  144. commonly used for antenna feed lines at amateur stations?
  145. A. Around 25 and 30 ohms
  146. B. Around 50 and 75 ohms
  147. C. Around 80 and 100 ohms
  148. D. Around 500 and 750 ohms
  149. *
  150. 271I-7.3   A 9-16  None
  151. What effect, if any, does the length of a coaxial cable have
  152. upon its characteristic impedance?
  153. A. The length has no effect on the characteristic impedance
  154. B. The length affects the characteristic impedance primarily
  155.    above 144 MHz
  156. C. The length affects the characteristic impedance primarily
  157.    below 144 MHz
  158. D. The length affects the characteristic impedance at any
  159.    frequency
  160. *
  161. 272I-7.4   D 9-14  300 Ω
  162. What is the characteristic impedance of flat-ribbon TV-type
  163. twinlead?
  164. A. 50 ohms
  165. B. 75 ohms
  166. C. 100 ohms
  167. D. 300 ohms
  168. *
  169. 273I-8.4   C 9-17  A mismatch between the antenna and|feedline, ie. a difference between|the line and feed-point impedances
  170. What is the cause of power being reflected back down an antenna
  171. feed line?
  172. A. Operating an antenna at its resonant frequency
  173. B. Using more transmitter power than the antenna can handle
  174. C. A difference between feed line impedance and antenna feed-
  175.    point impedance
  176. D. Feeding the antenna with unbalanced feed line
  177. *
  178. 274I-9.3   A 9-17  SWR = R/Zo,  SWR = 200/50,  SWR = 4:1|Second digit always 1
  179. What will be the standing wave ratio when a 50 ohm feed line
  180. is connected to a resonant antenna having a 200 ohm feed-point
  181. impedance?
  182. A. 4:1
  183. B. 1:4
  184. C. 2:1
  185. D. 1:2
  186. *
  187. 275I-9.4   D 9-17  SWR = Zo/R,  SWR = 50/10,  SWR = 5:1|Second digit always 1
  188. What will be the standing wave ratio when a 50 ohm feed line
  189. is connected to a resonant antenna having a 10 ohm feed-point
  190. impedance?
  191. A. 2:1
  192. B. 50:1
  193. C. 1:5
  194. D. 5:1
  195. *
  196. 276I-9.5   C 9-17  SWR = R/Zo,  SWR = 50/50,  SWR = 1:1|Second digit always 1
  197. What will be the standing wave ratio when a 50 ohm feed line
  198. is connected to a resonant antenna having a 50 ohm feed-point
  199. impedance?
  200. A. 2:1
  201. B. 50:50
  202. C. 1:1
  203. D. 0:0
  204. *
  205. 277I-11.1  C 9-16  Attenuation is independent|of Zo below 1.5 GHz
  206. How does the characteristic impedance of a coaxial cable affect
  207. the amount of attenuation to the RF signal passing through it?
  208. A. The attenuation is affected more by the characteristic
  209.    impedance at frequencies above 144 MHz than at frequencies
  210.    below 144 MHz
  211. B. The attenuation is affected less by the characteristic
  212.    impedance at frequencies above 144 MHz than at frequencies
  213.    below 144 MHz
  214. C. The attenuation related to the characteristic impedance is
  215.    about the same at all amateur frequencies below 1.5 GHz
  216. D. The difference in attenuation depends on the emission type
  217.    in use
  218. *
  219. 278I-11.2  A 9-16  The higher the frequency|the greater the losses  
  220. How does the amount of attenuation to a 2 meter signal passing
  221. through a coaxial cable differ from that to a 160 meter signal?
  222. A. The attenuation is greater at 2 meters
  223. B. The attenuation is less at 2 meters
  224. C. The attenuation is the same at both frequencies
  225. D. The difference in attenuation depends on the emission type
  226.    in use
  227. *
  228. 279I-11.4  D 9-14  Attenuation increases|when the lead is wet 
  229. What is the effect on its attenuation when flat-ribbon TV-type
  230. twinlead is wet?
  231. A. Attenuation decreases slightly
  232. B. Attenuation remains the same
  233. C. Attenuation decreases sharply
  234. D. Attenuation increases
  235. *
  236. 280I-11.7  B 9-15  To keep it dry
  237. Why might silicone grease or automotive car wax be applied to
  238. flat-ribbon TV-type twinlead?
  239. A. To reduce "skin effect" losses on the conductors
  240. B. To reduce the buildup of dirt and moisture on the feed line
  241. C. To increase the velocity factor of the feed line
  242. D. To help dissipate heat during high-SWR operation
  243. *
  244. 281I-11.8  D 9-14  dB per hundred feet
  245. In what values are RF feed line losses usually expressed?
  246. A. Bels/1000 ft
  247. B. dB/1000 ft
  248. C. Bels/100 ft
  249. D. dB/100 ft
  250. *
  251. 282I-11.10 D 9-14  The higher the frequency|the greater the losses  
  252. As the operating frequency increases, what happens to the
  253. dielectric losses in a feed line?
  254. A. The losses decrease
  255. B. The losses decrease to zero
  256. C. The losses remain the same
  257. D. The losses increase
  258. *
  259. 283I-11.12 A 9-14  As the operating frequency is|decreased the losses decrease
  260. As the operating frequency decreases, what happens to the
  261. dielectric losses in a feed line?
  262. A. The losses decrease
  263. B. The losses increase
  264. C. The losses remain the same
  265. D. The losses become infinite
  266. *
  267. 284I-12.1  D 9-17  The impedances of the transmission  |line and the antenna feed-point must|be matched
  268. What condition must be satisfied to prevent standing waves of
  269. voltage and current on an antenna feed line?
  270. A. The antenna feed point must be at DC ground potential
  271. B. The feed line must be an odd number of electrical quarter
  272.    wavelengths long
  273. C. The feed line must be an even number of physical half
  274.    wavelengths long
  275. D. The antenna feed-point impedance must be matched to the
  276.    characteristic impedance of the feed line
  277. *
  278. 285I-12.2  A 9-18  The answer to this question is A,  but|inductive coupling is used in resonant|antenna systems other than dipoles    
  279. How is an inductively-coupled matching network used in an antenna
  280. system consisting of a center-fed resonant dipole and coaxial feed
  281. line?
  282. A. An inductively coupled matching network is not normally used in
  283.    a resonant antenna system                                    
  284. B. An inductively coupled matching network is used to increase the
  285.    SWR to an acceptable level
  286. C. An inductively coupled matching network can be used to match the
  287.    unbalanced condition at the transmitter output to the balanced
  288.    condition required by the coaxial line
  289. D. An inductively coupled matching network can be used at the
  290.    antenna feed point to tune out the radiation resistance
  291. *
  292. 286I-12.5  D 9-17  A mismatch occurs when the impedance|of the feed line does not match the |feed-point impedance of the antenna 
  293. What is an antenna-transmission line mismatch?
  294. A. A condition where the feed-point impedance of the antenna
  295.    does not equal the output impedance of the transmitter
  296. B. A condition where the output impedance of the transmitter
  297.    does not equal the characteristic impedance of the feed line
  298. C. A condition where a half-wavelength antenna is being fed with
  299.    a transmission line of some length other than one-quarter
  300.    wavelength at the operating frequency
  301. D. A condition where the characteristic impedance of the feed
  302.    line does not equal the feed-point impedance of the antenna
  303. *
  304. 
  305.